Bonjour,

Je cherche à faire un pont entre ma broadcom 43xx et une carte ethernet standard 10/100.

Voilà, j'arrive à installer la carte réseau, mais en fait ca marche pas !

J'essaye d'utiliser hostap car j'ai vu que celui-ci gère le pont WiFi/Ethernet.Et quand je lance hostapd j'ai ceci :

HEXA:~# hostapd -d /etc/hostapd/hostapd.conf
Configuration file: /etc/hostapd/hostapd.conf
ctrl_interface_group=0
Configure bridge br0 for EAPOL traffic.
madwifi_set_iface_flags: dev_up=0
madwifi_set_privacy: enabled=0
ioctl[IEEE80211_IOCTL_SETPARAM]: Invalid argument
Using interface eth1 with hwaddr 00:0c:41:64:fe:cf and ssid 'MADOUIFI'
SSID - hexdump_ascii(len=8):
     4d 41 44 4f 55 49 46 49                           MADOUIFI
PSK (ASCII passphrase) - hexdump_ascii(len=36):
     53 75 70 e8 52 65 63 6c e9 44 65 6c 41 6d 6f 72   Sup_Recl_DelAmor
     2c 41 76 65 63 64 65 74 72 75 63 63 68 33 6c 30   ,Avecdetrucch3l0
     75 73 3b 29                                       us
PSK (from passphrase) - hexdump(len=32): ae f9 32 e4 5c d7 33 c7 ab ed bb 9e 25 c7 4e 88 cd 21 ec 43 23 79 3b 3d a7 86 7a 29 77 d4 01 c6
madwifi_set_ieee8021x: enabled=1
madwifi_configure_wpa: group key cipher=1
ioctl[IEEE80211_IOCTL_SETPARAM]: Invalid argument
Unable to set group key cipher to 1
eth1: DRIVER Error configuring WPA state!
IEEE 802.1X initialization failed.
rmdir[ctrl_interface]: No such file or directory
madwifi_set_ieee8021x: enabled=0
ioctl[IEEE80211_IOCTL_SETPARAM]: No such device
madwifi_set_iface_flags: dev_up=0
HEXA:~/wifi/ieee80211-1.2.17#

Et si je fait dmesg :

bcm43xx: PHY connected
bcm43xx: Microcode rev 0x127, pl 0xe (2005-04-18  02:36:27)
bcm43xx: Radio turned on
bcm43xx: Chip initialized
bcm43xx: 32-bit DMA initialized
bcm43xx: Keys cleared
bcm43xx: Selected 802.11 core (phytype 2)
ADDRCONF(NETDEV_UP): eth1: link is not ready
printk: 81 messages suppressed.
bcm43xx: FATAL ERROR: BCM43xx_IRQ_XMIT_ERROR
bcm43xx: FATAL ERROR: BCM43xx_IRQ_XMIT_ERROR
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: FATAL ERROR: BCM43xx_IRQ_XMIT_ERROR
bcm43xx: FATAL ERROR: BCM43xx_IRQ_XMIT_ERROR
bcm43xx: FATAL ERROR: BCM43xx_IRQ_XMIT_ERROR
bcm43xx: FATAL ERROR: BCM43xx_IRQ_XMIT_ERROR
bcm43xx: FATAL ERROR: BCM43xx_IRQ_XMIT_ERROR
bcm43xx: FATAL ERROR: BCM43xx_IRQ_XMIT_ERROR
bcm43xx: FATAL ERROR: BCM43xx_IRQ_XMIT_ERROR
bcm43xx: FATAL ERROR: BCM43xx_IRQ_XMIT_ERROR
bcm43xx: Radio turned off
bcm43xx: DMA-32 0x0200 (RX) max used slots: 1/64
bcm43xx: DMA-32 0x02A0 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0280 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0260 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0240 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0220 (TX) max used slots: 2/512
bcm43xx: DMA-32 0x0200 (TX) max used slots: 0/512
br0: port 1(eth1) entering disabled state
bcm43xx: set_interfmode allowed parameters are: 0 => None,  1 => Non-WLAN,  2 => WLAN,  3 => Auto-WLAN
bcm43xx: set_interfmode allowed parameters are: 0 => None,  1 => Non-WLAN,  2 => WLAN,  3 => Auto-WLAN
bcm43xx: Interference Mitigation mode Auto-WLAN not supported while the interface is down.

Voilà, je ne sait plus quoi faire !

PS : J'en ai absolument rien à faire du fait que hostapd gère le WPA. Si il y as une solution en WEP cella irras très bien !

Le seul truc que je veux est que mon WiFi AP soir SUR LE MEME réseau IP que ma carte ethernet ---> pas de passerelle.

Merci de m'éclairer un peut ...

___________________________
Le site de Galoula France !
[www.galoula.com]

Poste le Wednesday 4 April 2007 15:16:45