Re
alors là y'a la totale , je te laisse regarder :
# /usr/sbin/smartctl -a /dev/hda
smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen
Home page is [
smartmontools.sourceforge.net]
=== START OF INFORMATION SECTION ===
Device Model: Maxtor 52049U4
Serial Number: K40CPWNC
Firmware Version: DA620XS0
Device is: In smartctl database [for details use: -P show]
ATA Version is: 4
ATA Standard is: ATA/ATAPI-4 T13 1153D revision 17
Local Time is: Fri Oct 7 13:14:05 2005 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x1b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 15) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000a 253 252 000 Old_age Always - 35111357900684
3 Spin_Up_Time 0x0027 222 219 063 Pre-fail Always - 51
4 Start_Stop_Count 0x0032 253 253 000 Old_age Always - 405
5 Reallocated_Sector_Ct 0x0033 253 253 063 Pre-fail Always - 0
6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail Offline - 0
7 Seek_Error_Rate 0x000a 168 168 000 Old_age Always - 322122604987
8 Seek_Time_Performance 0x0027 253 240 187 Pre-fail Always - 238314850550206
9 Power_On_Minutes 0x0032 250 250 000 Old_age Always - 1342h+30m
10 Spin_Retry_Count 0x002b 253 252 223 Pre-fail Always - 97
11 Calibration_Retry_Count 0x002b 253 252 223 Pre-fail Always - 91
12 Power_Cycle_Count 0x0032 248 248 000 Old_age Always - 2342
196 Reallocated_Event_Count 0x0008 253 253 000 Old_age Offline - 0
197 Current_Pending_Sector 0x0008 253 253 000 Old_age Offline - 0
198 Offline_Uncorrectable 0x0008 253 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0008 199 199 000 Old_age Offline - 120
200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age Always - 362051
201 Soft_Read_Error_Rate 0x000a 253 252 000 Old_age Always - 163209013132
202 TA_Increase_Count 0x000a 001 001 000 Old_age Always - 96383361345420
203 Run_Out_Cancel 0x000b 197 196 180 Pre-fail Always - 120031451277196
204 Shock_Count_Write_Opern 0x000a 253 252 000 Old_age Always - 255884
205 Shock_Rate_Write_Opern 0x000a 253 252 000 Old_age Always - 255884
207 Spin_High_Current 0x002a 253 252 000 Old_age Always - 97
208 Spin_Buzz 0x002a 253 252 000 Old_age Always - 97
209 Offline_Seek_Performnce 0x0024 253 253 000 Old_age Offline - 0
96 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
97 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
98 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
99 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
100 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
101 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
SMART Error Log Version: 1
Warning: ATA error count 7913 inconsistent with error log pointer 5
ATA Error Count: 7913 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm
S.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 7913 occurred at disk power-on lifetime: 1251 hours (52 days + 3 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 01 00 00 a0 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
a1 ff 00 01 00 00 a0 08 00:00:11.280 IDENTIFY PACKET DEVICE
20 ff 01 01 00 00 a0 08 00:00:11.264 READ SECTOR(S)
b0 d9 f1 00 4f c2 a0 08 00:00:11.184 SMART DISABLE OPERATIONS
b0 d2 f1 00 4f c2 a0 08 00:00:11.136 SMART ENABLE/DISABLE ATTRIBUTE AUTOSAVE
b0 d8 3f 00 4f c2 a0 08 00:00:11.024 SMART ENABLE OPERATIONS
Error 7912 occurred at disk power-on lifetime: 1251 hours (52 days + 3 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 01 00 00 a0 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
a1 ff 00 01 00 00 a0 08 00:00:11.824 IDENTIFY PACKET DEVICE
20 ff 01 01 00 00 a0 08 00:00:11.808 READ SECTOR(S)
b0 d9 f1 00 4f c2 a0 08 00:00:11.744 SMART DISABLE OPERATIONS
b0 d2 f1 00 4f c2 a0 08 00:00:11.712 SMART ENABLE/DISABLE ATTRIBUTE AUTOSAVE
b0 d8 3f 00 4f c2 a0 08 00:00:11.552 SMART ENABLE OPERATIONS
Error 7911 occurred at disk power-on lifetime: 1251 hours (52 days + 3 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 01 00 00 a0 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
a1 ff 00 01 00 00 a0 08 00:00:11.760 IDENTIFY PACKET DEVICE
20 ff 01 01 00 00 a0 08 00:00:11.744 READ SECTOR(S)
b0 d9 f1 00 4f c2 a0 08 00:00:11.664 SMART DISABLE OPERATIONS
b0 d2 f1 00 4f c2 a0 08 00:00:11.616 SMART ENABLE/DISABLE ATTRIBUTE AUTOSAVE
b0 d8 3f 00 4f c2 a0 08 00:00:11.504 SMART ENABLE OPERATIONS
Error 7910 occurred at disk power-on lifetime: 1251 hours (52 days + 3 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 01 00 00 a0 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
a1 ff 00 01 00 00 a0 08 00:00:11.776 IDENTIFY PACKET DEVICE
20 ff 01 01 00 00 a0 08 00:00:11.760 READ SECTOR(S)
b0 d9 f1 00 4f c2 a0 08 00:00:11.696 SMART DISABLE OPERATIONS
b0 d2 f1 00 4f c2 a0 08 00:00:11.648 SMART ENABLE/DISABLE ATTRIBUTE AUTOSAVE
b0 d8 3f 00 4f c2 a0 08 00:00:11.520 SMART ENABLE OPERATIONS
Error 7909 occurred at disk power-on lifetime: 1251 hours (52 days + 3 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 01 00 00 a0 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
a1 ff 00 01 00 00 a0 08 00:00:11.824 IDENTIFY PACKET DEVICE
20 ff 01 01 00 00 a0 08 00:00:11.808 READ SECTOR(S)
b0 d9 f1 00 4f c2 a0 08 00:00:11.744 SMART DISABLE OPERATIONS
b0 d2 f1 00 4f c2 a0 08 00:00:11.680 SMART ENABLE/DISABLE ATTRIBUTE AUTOSAVE
b0 d8 3f 00 4f c2 a0 08 00:00:11.584 SMART ENABLE OPERATIONS
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
Device does not support Selective Self Tests/Logging
apparemment y'a des erreurs dans ce qu'il voit !
si vous me voyer une soluce ce serait bien sympa
encore merci pour votre aide journalière
et a tout à l'heure
bon ap' tout le monde !!
merci
chobu