'ttention, c'est long.

Bonjour,

Pour mon retour à un Linux dont je comprends les agissements, et qui ne cache pas toute la config, je viens d'installer une slack 10.2, dont j'ai remplacé le noyau 2.4 par le 2.6.13 selon le tuto de [franck.barbenoire.free.fr] .

Sortie de l'uname :

Linux #darkstar 2.6.13 #1 Sat Sep 3 21:11:20 PDT 2005 i686 unknown unknown GNU/Linux

Premier problème : mon lecteur de cartes multi-formats, qui me sert à lire les CF de mon APN, semble reconnu, mais l'insertion de la carte ne paraît pas être détectée. L'insertion de ma carte usb, elle, se traduit par des messages normaux et habituels :

May 10 22:14:13 #darkstar kernel: usb 1-6: new high speed USB device using ehci_hcd and address 6
May 10 22:14:13 #darkstar kernel: scsi1 : SCSI emulation for USB Mass Storage devices
May 10 22:14:18 #darkstar kernel:   Vendor: Kingston  Model: DataTraveler 2.0  Rev: 1.04
May 10 22:14:18 #darkstar kernel:   Type:   Direct-Access                      ANSI SCSI revision: 00
May 10 22:14:19 #darkstar kernel: SCSI device sdb: 2007040 512-byte hdwr sectors (1028 M
May 10 22:14:19 #darkstar kernel: sdb: Write Protect is off
May 10 22:14:19 #darkstar kernel: SCSI device sdb: 2007040 512-byte hdwr sectors (1028 M
May 10 22:14:19 #darkstar kernel: sdb: Write Protect is off
May 10 22:14:19 #darkstar kernel:  sdb: sdb1
May 10 22:14:19 #darkstar kernel: Attached scsi removable disk sdb at scsi1, channel 0, id 0, lun 0

Mon dmesg (j'ai mis entre *** les messages qui me semblent pertinents) :

Linux version 2.6.13 (root@midas) (gcc version 3.3.6) #1 Sat Sep 3 21:11:20 PDT 2005
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003fffc000 (usable)
 BIOS-e820: 000000003fffc000 - 000000003ffff000 (ACPI data)
 BIOS-e820: 000000003ffff000 - 0000000040000000 (ACPI NVS)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
Warning only 896MB will be used.
Use a HIGHMEM enabled kernel.
896MB LOWMEM available.
On node 0 totalpages: 229376
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 225280 pages, LIFO batch:31
  HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 ASUS                                  ) @ 0x000f5f40
ACPI: RSDT (v001 ASUS   A7V600-F 0x42302e31 MSFT 0x31313031) @ 0x3fffc000
ACPI: FADT (v001 ASUS   A7V600-F 0x42302e31 MSFT 0x31313031) @ 0x3fffc0b2
ACPI: BOOT (v001 ASUS   A7V600-F 0x42302e31 MSFT 0x31313031) @ 0x3fffc030
ACPI: MADT (v001 ASUS   A7V600-F 0x42302e31 MSFT 0x31313031) @ 0x3fffc058
ACPI: DSDT (v001   ASUS A7V600-F 0x00001000 MSFT 0x0100000b) @ 0x00000000
ACPI: PM-Timer IO Port: 0xe408
Allocating PCI resources starting at 40000000 (gap: 40000000:bec00000)
Built 1 zonelists
Kernel command line: root=/dev/hda3 ro
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 2000.341 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 905372k/917504k available (1925k kernel code, 11544k reserved, 879k data, 160k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 4004.39 BogoMIPS (lpj=8008796)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000020 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
mtrr: v2.0 (20020519)
CPU: AMD Athlon(TM) XP 2400+ stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 0a20)
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 373k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf1990, last bus=1
PCI: Using configuration type 1
ACPI: Subsystem revision 20050408
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 9 10 11 12)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *9 10 11 12)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 *11 12)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 11 12) *15, disabled.
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] segment is 0
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI: Bridge: 0000:00:01.0
  IO window: d000-dfff
  MEM window: df000000-dfffffff
  PREFETCH window: e0000000-f7ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
Simple Boot Flag at 0x3a set to 0x1
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
PCI: Enabling device 0000:00:0b.0 (0094 -> 0097)
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
ttyS1 at I/O 0xb408 (irq = 11) is a 16450
ttyS2 at I/O 0xb410 (irq = 11) is a 8250
ttyS3 at I/O 0xb418 (irq = 11) is a 16450
Couldn't register serial port 0000:00:0b.0: -28
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.0
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [LNKE] -> GSI 5 (level, low) -> IRQ 5
PCI: Via IRQ fixup for 0000:00:0f.0, from 255 to 5
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.0
    ide0: BM-DMA at 0xb000-0xb007, BIOS settings: hdaMA, hdb:pio
    ide1: BM-DMA at 0xb008-0xb00f, BIOS settings: hdcMA, hddMA
Probing IDE interface ide0...
hda: Maxtor 6Y080L0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: HL-DT-STDVD-ROM GDR8162B, ATAPI CD/DVD-ROM drive
hdd: _NEC DVD+RW ND-1100A, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 160086528 sectors (81964 M w/2048KiB Cache, CHS=65535/16/63, UDMA(133)
hda: cache flushes supported
 hda: hda1 hda2 hda3 hda4 < hda5 hda6 >
hdc: ATAPI 32X DVD-ROM drive, 256kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 40X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
ide-floppy driver 0.99.newide
usbmon: debugfs is not available
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
mice: PS/2 mouse device common for all mice
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard on isa0060/serio0
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
ACPI wakeup devices: 
PCI0 PCI1 USB0 USB1 USB2 USB3 SU20 MC97 SLAN 
ACPI: (supports S0 S1 S3 S4 S5)
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 160k freed
Adding 995988k swap on /dev/hda5.  Priority:-1 extents:1
EXT3 FS on hda3, internal journal
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
Linux agpgart interface v0.101 (c) Dave Jones
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker
ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LNKE] -> GSI 5 (level, low) -> IRQ 5
eth0: VIA Rhine II at 0xdd000000, 00:0c:6e:a4:89:09, IRQ 5.
eth0: MII PHY found at address 1, status 0x7849 advertising 01e1 Link 0000.
ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [LNKG] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:11.5 to 64
***ALSA /tmp/alsa-driver-1.0.9b/alsa-kernel/pci/via82xx.c:583: codec_read: codec 0 is not valid [0xfe0000]
ALSA /tmp/alsa-driver-1.0.9b/alsa-kernel/pci/via82xx.c:583: codec_read: codec 0 is not valid [0xfe0000]
ALSA /tmp/alsa-driver-1.0.9b/alsa-kernel/pci/via82xx.c:583: codec_read: codec 0 is not valid [0xfe0000]
ALSA /tmp/alsa-driver-1.0.9b/alsa-kernel/pci/via82xx.c:583: codec_read: codec 0 is not valid [0xfe0000]***
ACPI: PCI Interrupt 0000:00:10.4[C] -> Link [LNKG] -> GSI 11 (level, low) -> IRQ 11
ehci_hcd 0000:00:10.4: VIA Technologies, Inc. USB 2.0
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.4: irq 11, io mem 0xdd800000
ehci_hcd 0000:00:10.4: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
USB Universal Host Controller Interface driver v2.3
usb 1-1: new high speed USB device using ehci_hcd and address 2
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKE] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: irq 5, io base 0x0000a800
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
ACPI: PCI Interrupt 0000:00:10.1[A] -> Link [LNKE] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: irq 5, io base 0x0000a400
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKF] BIOS reported IRQ 0, using IRQ 9
ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 9
PCI: setting IRQ 9 as level-triggered
ACPI: PCI Interrupt 0000:00:10.2 -> Link [LNKF] -> GSI 9 (level, low) -> IRQ 9
uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3)
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: irq 9, io base 0x0000a000
usb 2-2: new low speed USB device using uhci_hcd and address 2
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3 -> Link [LNKF] -> GSI 9 (level, low) -> IRQ 9
PCI: Via IRQ fixup for 0000:00:10.3, from 0 to 9
uhci_hcd 0000:00:10.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#4)
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:10.3: irq 9, io base 0x00009800
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb 3-1: new low speed USB device using uhci_hcd and address 2
input: USB HID v1.00 Mouse [1241:1155] on usb-0000:00:10.1-1
usb 3-2: new full speed USB device using uhci_hcd and address 3
drivers/usb/input/aiptek.c: input: Aiptek on usb-0000:00:10.0-2 (event3)

ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1299 $ Ben Collins <bcollins@debian.org>
PCI: Enabling device 0000:00:07.0 (0094 -> 0097)
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
PCI: Via IRQ fixup for 0000:00:07.0, from 255 to 10
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[10]  MMIO=[de800000-de8007ff]  Max Packet=[2048]
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
agpgart: Detected VIA KT400/KT400A/KT600 chipset
agpgart: AGP aperture is 64M @ 0xf8000000
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
***shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
  Vendor: USB2.0    Model: CardReader CF RW  Rev: 0.0>
  Type:   Direct-Access                      ANSI SCSI revision: 00
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0***
usb-storage: device scan complete
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00e01800003015f0]
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
drivers/usb/input/aiptek.c: input: Aiptek using 400 ms programming speed

usbcore: registered new driver aiptek
drivers/usb/input/aiptek.c: v1.5 (May-15-2004): Bryan W. Headley/Chris Atenasio
drivers/usb/input/aiptek.c: Aiptek HyperPen USB Tablet Driver (Linux 2.6.x)
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
NET: Registered protocol family 10
Disabled Privacy Extensions on device c0385400(lo)
IPv6 over IPv4 tunneling driver
lp: driver loaded but no devices found
[drm] Initialized drm 1.0.0 20040925
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[drm] Initialized radeon 1.16.0 20050311 on minor 0: ATI Technologies Inc RV280 [Radeon 9200 SE]
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 4x mode
[drm] Loading R200 Microcode

Je ne vous cache pas que j'ai plus l'habitude du dmesg de FreeBSD, et que celui de Linux (la dernière fois que j'ai vraiment mis les mains dans le cambouis, c'était avec les noyaux 2.2...) me semble quelque peu opaque.

lsmod me donne ceci :

Module                  Size  Used by
radeon                 73600  1 
drm                    56852  2 radeon
snd_pcm_oss            46240  1 
snd_mixer_oss          15872  1 snd_pcm_oss
lp                      9928  0 
parport                30024  1 lp
ipv6                  225600  10 
ohci_hcd               18436  0 
via_agp                 7552  1 
joydev                  8000  0 
aiptek                 17792  0 
ohci1394               30388  0 
ieee1394               85304  1 ohci1394
usb_storage            68416  0 
uhci_hcd               29584  0 
ehci_hcd               29704  0 
i2c_viapro              6928  0 
i2c_core               16656  1 i2c_viapro
snd_via82xx            22592  1 
gameport               11144  1 snd_via82xx
snd_ac97_codec         75388  1 snd_via82xx
snd_pcm                75016  3 snd_pcm_oss,snd_via82xx,snd_ac97_codec
snd_timer              19716  1 snd_pcm
snd_page_alloc          7556  2 snd_via82xx,snd_pcm
snd_mpu401_uart         5888  1 snd_via82xx
snd_rawmidi            19232  1 snd_mpu401_uart
snd_seq_device          6924  1 snd_rawmidi
snd                    45572  9 snd_pcm_oss,snd_mixer_oss,snd_via82xx,snd_ac97_codec,snd_pcm,snd_timer,snd_mpu401_uart,snd_rawmidi,snd_seq_device
soundcore               6880  2 snd
via_rhine              19332  0 
mii                     4608  1 via_rhine
evdev                   7296  0 
agpgart                28616  2 drm,via_agp
psmouse                29956  0 
ext3                  122504  2 
jbd                    48024  1 ext3

Autre problème : le son. J'ai bien "unmuté" dans alsamixer, aumix -q me le confirme. Mais le dmesg semble me dire qu'il y a un problème de codecs, alors que la version 1.0.9b des modules alsa est bien celle qui va avec le noyau 2.6.13.

Pour info, je vous fournis les infos données par la Ubuntu qui traîne à côté, et qui je l'espère vit ses derniers instants :

l'uname :

Linux aboulafia 2.6.12-9-386 #1 Mon Oct 10 13:14:36 BST 2005 i686 GNU/Linux

le dmesg :

942000] Linux Plug and Play Support v0.97 (c) Adam Belay
[4294671.942000] pnp: PnP ACPI init
[4294671.946000] pnp: PnP ACPI: found 12 devices
[4294671.946000] PnPBIOS: Disabled by ACPI PNP
[4294671.946000] PCI: Using ACPI for IRQ routing
[4294671.946000] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[4294671.951000] pnp: 00:01: ioport range 0xe400-0xe47f could not be reserved
[4294671.951000] pnp: 00:01: ioport range 0xe800-0xe81f has been reserved
[4294671.951000] pnp: 00:0b: ioport range 0x290-0x297 has been reserved
[4294671.951000] pnp: 00:0b: ioport range 0x370-0x375 has been reserved
[4294671.951000] Simple Boot Flag at 0x3a set to 0x1
[4294671.951000] audit: initializing netlink socket (disabled)
[4294671.951000] audit: initialized
[4294671.951000] highmem bounce pool size: 64 pages
[4294671.952000] VFS: Disk quotas dquot_6.5.1
[4294671.952000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[4294671.952000] devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
[4294671.952000] devfs: boot_options: 0x0
[4294671.952000] Initializing Cryptographic API
[4294671.952000] isapnp: Scanning for PnP cards...
[4294672.305000] isapnp: No Plug & Play device found
[4294672.322000] PNP: PS/2 controller doesn't have AUX irq; using default 0xc
[4294672.322000] PNP: PS/2 Controller [PNP0303S2K] at 0x60,0x64 irq 112
[4294672.327000] serio: i8042 AUX port at 0x60,0x64 irq 12
[4294672.327000] serio: i8042 KBD port at 0x60,0x64 irq 1
[4294672.327000] Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
[4294672.328000] ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[4294672.329000] ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[4294672.329000] PCI: Enabling device 0000:00:0b.0 (0094 -> 0097)
[4294672.329000] ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 19 (level, low) -> IRQ 19
[4294672.330000] ttyS15 at I/O 0xb408 (irq = 19) is a 16450
[4294672.330000] ttyS50 at I/O 0xb410 (irq = 19) is a 8250
[4294672.330000] ttyS51 at I/O 0xb418 (irq = 19) is a 16450
[4294672.330000] ttyS52 at I/O 0xb420 (irq = 19) is a 8250
[4294672.330000] ttyS53 at I/O 0xb428 (irq = 19) is a 8250
[4294672.331000] io scheduler noop registered
[4294672.331000] io scheduler anticipatory registered
[4294672.331000] io scheduler deadline registered
[4294672.331000] io scheduler cfq registered
[4294672.332000] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[4294672.333000] EISA: Probing bus 0 at eisa.0
[4294672.333000] EISA: Detected 0 cards.
[4294672.333000] NET: Registered protocol family 2
[4294672.343000] IP: routing cache hash table of 8192 buckets, 64Kbytes
[4294672.344000] TCP established hash table entries: 262144 (order: 9, 2097152 bytes)
[4294672.348000] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
[4294672.348000] TCP: Hash tables configured (established 262144 bind 65536)
[4294672.348000] NET: Registered protocol family 8
[4294672.348000] NET: Registered protocol family 20
[4294672.349000] ACPI wakeup devices: 
[4294672.349000] PCI0 PCI1 USB0 USB1 USB2 USB3 SU20 MC97 SLAN 
[4294672.349000] ACPI: (supports S0 S1 S3 S4 S5)
[4294672.349000] Freeing unused kernel memory: 224k freed
[4294672.375000] input: AT Translated Set 2 keyboard on isa0060/serio0
[4294672.386000] vga16fb: initializing
[4294672.386000] vga16fb: mapped to 0xc00a0000
[4294672.489000] Console: switching to colour frame buffer device 80x30
[4294672.489000] fb0: VGA16 VGA frame buffer device
[4294673.628000] Capability LSM initialized
[4294673.639000] NET: Registered protocol family 1
[4294673.651000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[4294673.651000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[4294673.651000] ACPI: bus type ide registered
[4294673.658000] VP_IDE: IDE controller at PCI slot 0000:00:0f.0
[4294673.658000] ACPI: PCI Interrupt 0000:00:0f.0[A] -> GSI 20 (level, low) -> IRQ 20
[4294673.658000] PCI: Via IRQ fixup for 0000:00:0f.0, from 255 to 4
[4294673.658000] VP_IDE: chipset revision 6
[4294673.658000] VP_IDE: not 100% native mode: will probe irqs later
[4294673.658000] VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.0
[4294673.658000]     ide0: BM-DMA at 0xb000-0xb007, BIOS settings: hdaMA, hdb:pio
[4294673.658000]     ide1: BM-DMA at 0xb008-0xb00f, BIOS settings: hdcMA, hddMA
[4294673.658000] Probing IDE interface ide0...
[4294674.042000] hda: Maxtor 6Y080L0, ATA DISK drive
[4294674.654000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[4294674.654000] Probing IDE interface ide1...
[4294675.446000] hdc: HL-DT-STDVD-ROM GDR8162B, ATAPI CD/DVD-ROM drive
[4294676.160000] hdd: _NEC DVD+RW ND-1100A, ATAPI CD/DVD-ROM drive
[4294676.218000] ide1 at 0x170-0x177,0x376 on irq 15
[4294676.218000] Probing IDE interface ide2...
[4294676.731000] Probing IDE interface ide3...
[4294677.243000] Probing IDE interface ide4...
[4294677.755000] Probing IDE interface ide5...
[4294678.270000] hda: max request size: 128KiB
[4294678.286000] hda: 160086528 sectors (81964 M w/2048KiB Cache, CHS=65535/16/63, UDMA(133)
[4294678.286000] hda: cache flushes supported
[4294678.286000]  /dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4 < p5 p6 >
[4294678.325000] hdc: ATAPI 32X DVD-ROM drive, 256kB Cache
[4294678.325000] Uniform CD-ROM driver Revision: 3.20
[4294678.340000] hdd: ATAPI 40X DVD-ROM CD-R/RW drive, 2048kB Cache
[4294678.702000] Attempting manual resume
[4294678.714000] swsusp: Suspend partition has wrong signature?
[4294678.759000] usbcore: registered new driver usbfs
[4294678.759000] usbcore: registered new driver hub
[4294678.760000] USB Universal Host Controller Interface driver v2.2
[4294678.760000] ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
[4294678.760000] PCI: Via IRQ fixup for 0000:00:10.0, from 0 to 5
[4294678.760000] uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
[4294678.822000] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
[4294678.822000] uhci_hcd 0000:00:10.0: irq 21, io base 0x0000a800
[4294678.822000] hub 1-0:1.0: USB hub found
[4294678.822000] hub 1-0:1.0: 2 ports detected
[4294678.825000] ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 21
[4294678.825000] PCI: Via IRQ fixup for 0000:00:10.1, from 0 to 5
[4294678.825000] uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
[4294678.887000] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
[4294678.887000] uhci_hcd 0000:00:10.1: irq 21, io base 0x0000a400
[4294678.887000] hub 2-0:1.0: USB hub found
[4294678.887000] hub 2-0:1.0: 2 ports detected
[4294678.890000] ACPI: PCI Interrupt 0000:00:10.2 -> GSI 21 (level, low) -> IRQ 21
[4294678.890000] PCI: Via IRQ fixup for 0000:00:10.2, from 0 to 5
[4294678.890000] uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3)
[4294678.952000] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
[4294678.952000] uhci_hcd 0000:00:10.2: irq 21, io base 0x0000a000
[4294678.952000] hub 3-0:1.0: USB hub found
[4294678.952000] hub 3-0:1.0: 2 ports detected
[4294678.955000] ACPI: PCI Interrupt 0000:00:10.3 -> GSI 21 (level, low) -> IRQ 21
[4294678.955000] PCI: Via IRQ fixup for 0000:00:10.3, from 0 to 5
[4294678.955000] uhci_hcd 0000:00:10.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#4)
[4294678.991000] usb 1-1: new full speed USB device using uhci_hcd and address 2
[4294679.017000] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
[4294679.017000] uhci_hcd 0000:00:10.3: irq 21, io base 0x00009800
[4294679.017000] hub 4-0:1.0: USB hub found
[4294679.017000] hub 4-0:1.0: 2 ports detected
[4294679.050000] ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21
[4294679.050000] PCI: Via IRQ fixup for 0000:00:10.4, from 0 to 5
[4294679.050000] ehci_hcd 0000:00:10.4: VIA Technologies, Inc. USB 2.0
[4294679.050000] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
[4294679.050000] ehci_hcd 0000:00:10.4: irq 21, io mem 0xdd800000
[4294679.051000] ehci_hcd 0000:00:10.4: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
[4294679.051000] hub 5-0:1.0: USB hub found
[4294679.051000] hub 5-0:1.0: 8 ports detected
[4294679.095000] via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker
[4294679.095000] ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 23 (level, low) -> IRQ 23
[4294679.095000] PCI: Via IRQ fixup for 0000:00:12.0, from 0 to 7
[4294679.095000] eth0: VIA Rhine II at 0x19400, 00:0c:6e:a4:89:09, IRQ 23.
[4294679.096000] eth0: MII PHY found at address 1, status 0x7849 advertising 01e1 Link 0000.
[4294679.469000] usb 1-1: device not accepting address 2, error -71
[4294680.414000] usb 5-1: new high speed USB device using ehci_hcd and address 2
[4294681.125000] usb 1-2: new low speed USB device using uhci_hcd and address 4
[4294681.159000] SCSI subsystem initialized
[4294681.160000] Initializing USB Mass Storage driver...
[4294681.255000] scsi0 : SCSI emulation for USB Mass Storage devices
[4294681.255000] usb-storage: device found at 2
[4294681.255000] usb-storage: waiting for device to settle before scanning
[4294681.256000] usbcore: registered new driver usb-storage
[4294681.256000] USB Mass Storage support registered.
[4294681.422000] usb 2-1: new low speed USB device using uhci_hcd and address 2
[4294681.699000] usb 2-2: new full speed USB device using uhci_hcd and address 3
[4294681.733000] ACPI: CPU0 (power states: C1[C1])
[4294681.956000] Attempting manual resume
[4294681.956000] swsusp: Suspend partition has wrong signature?
[4294681.971000] kjournald starting.  Commit interval 5 seconds
[4294681.971000] EXT3-fs: mounted filesystem with ordered data mode.
[4294683.006000] md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
[4294686.258000]   Vendor: USB2.0    Model: CardReader CF RW  Rev: 0.0>
[4294686.258000]   Type:   Direct-Access                      ANSI SCSI revision: 00
[4294686.281000]   Vendor: USB2.0    Model: CardReader SD RW  Rev: 0.0>
[4294686.281000]   Type:   Direct-Access                      ANSI SCSI revision: 00
[4294686.285000]   Vendor: USB2.0    Model: CardReader SM RW  Rev: 0.0>
[4294686.285000]   Type:   Direct-Access                      ANSI SCSI revision: 00
[4294686.288000]   Vendor: USB2.0    Model: CardReader MS RW  Rev: 0.0>
[4294686.288000]   Type:   Direct-Access                      ANSI SCSI revision: 00
[4294686.291000] usb-storage: device scan complete
[4294686.723000] Adding 995988k swap on /dev/hda5.  Priority:-1 extents:1
[4294686.969000] EXT3 FS on hda6, internal journal
[4294688.216000] Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
[4294688.225000] Attached scsi removable disk sdb at scsi0, channel 0, id 0, lun 1
[4294688.232000] Attached scsi removable disk sdc at scsi0, channel 0, id 0, lun 2
[4294688.240000] Attached scsi removable disk sdd at scsi0, channel 0, id 0, lun 3
[4294693.576000] parport: PnPBIOS parport detected.
[4294693.577000] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[4294693.663000] lp0: using parport0 (interrupt-driven).
[4294693.733000] mice: PS/2 mouse device common for all mice
[4294693.771000] ieee1394: Initialized config rom entry `ip1394'
[4294693.788000] sbp2: $Rev: 1219 $ Ben Collins <bcollins@debian.org>
[4294697.332000] device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
[4294698.159000] cdrom: open failed.
[4294698.163000] cdrom: open failed.
[4294699.151000] kjournald starting.  Commit interval 5 seconds
[4294699.151000] EXT3 FS on hda2, internal journal
[4294699.151000] EXT3-fs: mounted filesystem with ordered data mode.
[4294699.159000] NTFS driver 2.1.22 [Flags: R/O MODULE].
[4294699.212000] NTFS volume version 3.1.
[4294700.716000] Linux agpgart interface v0.101 (c) Dave Jones
[4294700.727000] agpgart: Detected VIA KT400/KT400A/KT600 chipset
[4294700.750000] agpgart: AGP aperture is 64M @ 0xf8000000
[4294700.841000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[4294700.848000] shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
[4294700.848000] shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
[4294700.966000] ohci1394: $Rev: 1250 $ Ben Collins <bcollins@debian.org>
[4294700.966000] PCI: Enabling device 0000:00:07.0 (0094 -> 0097)
[4294700.966000] ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 17 (level, low) -> IRQ 17
[4294700.966000] PCI: Via IRQ fixup for 0000:00:07.0, from 255 to 1
[4294701.025000] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[17]  MMIO=[de800000-de8007ff]  Max Packet=[2048]
[4294701.798000] ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 22
[4294701.798000] PCI: Via IRQ fixup for 0000:00:11.5, from 0 to 6
[4294701.800000] PCI: Setting latency timer of device 0000:00:11.5 to 64
[4294702.291000] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00e01800003015f0]
[4294702.312000] codec_read: codec 0 is not valid [0xfe0000]
[4294702.318000] codec_read: codec 0 is not valid [0xfe0000]
[4294702.325000] codec_read: codec 0 is not valid [0xfe0000]
[4294702.331000] codec_read: codec 0 is not valid [0xfe0000]
[4294704.655000] usbcore: registered new driver hiddev
[4294704.660000] usbhid: probe of 1-2:1.0 failed with error -5
[4294704.752000] input: USB HID v1.00 Mouse [1241:1155] on usb-0000:00:10.1-1
[4294704.752000] usbcore: registered new driver usbhid
[4294704.752000] drivers/usb/input/hid-core.c: v2.01:USB HID core driver
[4294704.820000] drivers/usb/input/aiptek.c: input: Aiptek on usb-0000:00:10.0-2 (event2)
[4294704.820000] 
[4294705.164000] ts: Compaq touchscreen protocol output
[4294707.804000] drivers/usb/input/aiptek.c: input: Aiptek using 400 ms programming speed
[4294707.804000] 
[4294707.814000] usbcore: registered new driver aiptek
[4294707.814000] drivers/usb/input/aiptek.c: v1.5 (May-15-2004): Bryan W. Headley/Chris Atenasio
[4294707.814000] drivers/usb/input/aiptek.c: Aiptek HyperPen USB Tablet Driver (Linux 2.6.x)
[4294708.319000] Real Time Clock Driver v1.12
[4294708.425000] input: PC Speaker
[4294708.523000] Floppy drive(s): fd0 is 1.44M
[4294708.539000] FDC 0 is a post-1991 82077
[4294712.471000] ACPI: Power Button (FF) [PWRF]
[4294712.471000] ACPI: Power Button (CM) [PWRB]
[4294712.587000] ibm_acpi: ec object not found
[4294718.341000] [drm] Initialized drm 1.0.0 20040925
[4294718.352000] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[4294718.354000] [drm] Initialized radeon 1.16.0 20050311 on minor 0: ATI Technologies Inc RV280 [Radeon 9200 SE]
[4294718.355000] agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
[4294718.355000] agpgart: Putting AGP V3 device at 0000:00:00.0 into 4x mode
[4294718.355000] agpgart: Putting AGP V3 device at 0000:01:00.0 into 4x mode
[4294718.429000] [drm] Loading R200 Microcode
[4294721.183000] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[4294721.183000] apm: overridden by ACPI.
[4294722.468000] Bluetooth: Core ver 2.7
[4294722.468000] NET: Registered protocol family 31
[4294722.468000] Bluetooth: HCI device and connection manager initialized
[4294722.468000] Bluetooth: HCI socket layer initialized
[4294722.860000] Bluetooth: L2CAP ver 2.7
[4294722.860000] Bluetooth: L2CAP socket layer initialized
[4294722.950000] Bluetooth: RFCOMM ver 1.5
[4294722.950000] Bluetooth: RFCOMM socket layer initialized
[4294722.950000] Bluetooth: RFCOMM TTY layer initialized
[4294729.518000] NET: Registered protocol family 10
[4294729.518000] Disabled Privacy Extensions on device c02eb280(lo)
[4294729.518000] IPv6 over IPv4 tunneling driver

le lsmod :

Module                  Size  Used by
ipv6                  217408  6 
rfcomm                 34972  0 
l2cap                  22404  5 rfcomm
bluetooth              43012  4 rfcomm,l2cap
cpufreq_userspace       4444  0 
cpufreq_stats           5124  0 
freq_table              4484  1 cpufreq_stats
cpufreq_powersave       1920  0 
cpufreq_ondemand        5916  0 
cpufreq_conservative     6820  0 
radeon                 68352  1 
drm                    58004  2 radeon
video                  16004  0 
tc1100_wmi              6916  0 
sony_acpi               5516  0 
pcc_acpi               11392  0 
hotkey                  9508  0 
dev_acpi               11396  0 
i2c_acpi_ec             5760  0 
button                  6672  0 
battery                 9604  0 
container               4608  0 
ac                      4996  0 
floppy                 52692  0 
pcspkr                  3652  0 
rtc                    11832  0 
joydev                  9280  0 
tsdev                   7616  0 
aiptek                 18176  0 
usbhid                 30688  0 
snd_seq_dummy           3844  0 
snd_seq_oss            29440  0 
snd_seq_midi            8608  0 
snd_seq_midi_event      6656  2 snd_seq_oss,snd_seq_midi
snd_seq                44688  6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_via82xx            25792  1 
gameport               14472  1 snd_via82xx
snd_ac97_codec         72188  1 snd_via82xx
snd_pcm_oss            46368  0 
snd_mixer_oss          16128  1 snd_pcm_oss
snd_pcm                78344  3 snd_via82xx,snd_ac97_codec,snd_pcm_oss
snd_timer              21764  2 snd_seq,snd_pcm
snd_page_alloc         10120  2 snd_via82xx,snd_pcm
snd_mpu401_uart         6784  1 snd_via82xx
snd_rawmidi            22816  2 snd_seq_midi,snd_mpu401_uart
snd_seq_device          8204  5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq,snd_rawmidi
snd                    48644  13 snd_seq_oss,snd_seq,snd_via82xx,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer,snd_mpu401_uart,snd_rawmidi,snd_seq_device
soundcore               9184  1 snd
i2c_viapro              7696  0 
i2c_core               19728  2 i2c_acpi_ec,i2c_viapro
ohci1394               30644  0 
pci_hotplug            24628  0 
via_agp                 9472  1 
agpgart                32328  2 drm,via_agp
nls_cp437               5888  1 
ntfs                   92016  1 
dm_mod                 50364  1 
evdev                   9088  0 
sr_mod                 15652  0 
sbp2                   21128  0 
ieee1394               90936  2 ohci1394,sbp2
psmouse                26116  0 
mousedev               10912  1 
parport_pc             31812  1 
lp                     11460  0 
parport                32072  2 parport_pc,lp
sd_mod                 17424  0 
md                     40656  0 
ext3                  115976  2 
jbd                    48536  1 ext3
thermal                13192  0 
processor              23100  1 thermal
fan                     4740  0 
usb_storage            64704  0 
scsi_mod              124872  4 sr_mod,sbp2,sd_mod,usb_storage
via_rhine              20356  0 
mii                     5248  1 via_rhine
ehci_hcd               29448  0 
uhci_hcd               28048  0 
usbcore               104188  6 aiptek,usbhid,usb_storage,ehci_hcd,uhci_hcd
ide_cd                 36996  0 
cdrom                  33952  2 sr_mod,ide_cd
ide_disk               16128  5 
ide_generic             1664  0 
via82cxxx              12188  1 
ide_core              125268  5 usb_storage,ide_cd,ide_disk,ide_generic,via82cxxx
unix                   24624  646 
vesafb                  8088  0 
capability              5000  0 
commoncap               6784  1 capability
vga16fb                12232  1 
vgastate                8320  1 vga16fb
softcursor              2432  2 vesafb,vga16fb
cfbimgblt               2944  2 vesafb,vga16fb
cfbfillrect             3840  2 vesafb,vga16fb
cfbcopyarea             4480  2 vesafb,vga16fb
fbcon                  34176  72 
tileblit                2560  1 fbcon
font                    8448  1 fbcon
bitblit                 5248  1 fbcon

Voilà, merci d'avance de toute info et piste que vous pourrez me fournir sur ces deux problèmes.

--
Primo : rien de ce que j'écris ne saurait avoir a priori valeur de vérité universelle et incontournable.
Secundo : ce post est placé sous la DSSL (Demerden Sie Sich Licence).
Tertio : les barbus mangent du nioubie au p'tit-déj.
Quarto : z'avez vu, j'ai rajouté un tertio ?

Poste le Thursday 11 May 2006 12:06:04