Bonjour à tous,
Je me suis depuis peu remis sous Debian Etch avec KDE 3.5. Souhaitant installer un bootloader, j'ai tout d'abord tenter de compiler le noyau normalement. J'ai donc téléchargé le kernel 2.6.25.4 sur kernel.org, je l'ai compilé et installé en suivant divers tutos avec make-kpkg.
Seulement, au redémarrage, j'ai quelques "freezes" qui me ralentissent tout pendant plusieurs dizaines de secondes. Le noyau semble essayer de me charger sdc plusieurs fois avant d'abandonner... puis m'affiche plusieurs fois :
ata2: soft is slow to respond, please be patient.
ata2: SRST failed (erno=-16)
ata2: soft resetting link
Pour info :
Disk /dev/sda: 251.0 GB, 251000193024 bytes
255 heads, 63 sectors/track, 30515 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sda1 30454 30515 498015 82 Linux swap / Solaris
/dev/sda2 * 1 6079 48829536 83 Linux
/dev/sda3 6080 30453 195784155 7 HPFS/NTFS
Partition table entries are not in disk order
Disk /dev/sdb: 320.0 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sdb1 * 1 38914 312568832 7 HPFS/NTFS
sda2 est donc Debian et sdb1 Vista. Ces deux disques sont en SATA et mon graveur DVD en IDE.
Mon grub/menu.lst abrégé :
title Windows Vista
boot (hd1,0)
makeactive
chainloader +1
title Debian GNU/Linux, kernel 2.6.25.4.debiarkh
root (hd0,1)
kernel /boot/vmlinuz-2.6.25.4.debiarkh root=/dev/sda2 ro
initrd /boot/initrd.img-2.6.25.4.debiarkh
savedefault
title Debian GNU/Linux, kernel 2.6.25.4.debiarkh (single-user mode)
root (hd0,1)
kernel /boot/vmlinuz-2.6.25.4.debiarkh root=/dev/sda2 ro single
initrd /boot/initrd.img-2.6.25.4.debiarkh
savedefault
title Debian GNU/Linux, kernel 2.6.18-6-686
root (hd0,1)
kernel /boot/vmlinuz-2.6.18-6-686 root=/dev/sda2 ro
initrd /boot/initrd.img-2.6.18-6-686
savedefault
title Debian GNU/Linux, kernel 2.6.18-6-686 (single-user mode)
root (hd0,1)
kernel /boot/vmlinuz-2.6.18-6-686 root=/dev/sda2 ro single
initrd /boot/initrd.img-2.6.18-6-686
savedefault
Sauriez-vous donc comment éviter ces messages au démarrage? Cela provient surement d'une mauvaise conficuration du noyau avant compilation?
A propos, j'avais modifié mon .config après un Kernel panic au boot :
VFS: Cannot open root device "hda2" or unknown block (0,0)
Kernel panic - not syncing: VFS Unable to mount root fs on unknow block (0,0)
en remplaçant
CONFIG_PARTITION_ADVANCED=y
par
# CONFIG_PARTITION_ADVANCED is not set.
Merci à tous ceux qui sauraient me répondre ou même me mettre sur une piste